Search for: All records

AlGaN/GaN high electron mobility transistors (HEMTs) are in high demand for wireless communication and power conversion applications due to their high-power and high-frequency capabilities. However, the extremely high operational heat flux often leads to the formation of hotspots that negatively impact the device performance and reliability. In this work, an AlGaN/GaN HEMT with a transparent indium tin oxide (ITO) gate was fabricated to enable in situ characterization of the channel peak temperature that occurs underneath the gate electrode. Raman thermometry was performed to measure the temperature of the GaN layer under various bias conditions while power dissipation was kept constant. An electro-thermal device model was created to validate experimental results, to explain the physical origins of the bias-dependent self-heating behavior, and to calculate the peak temperature of the two-dimensional electron gas channel. Experimental results show that the temperature measured next to the drain side edge of the gate (which is a normal practice when characterizing a standard metal-gated device) resulted in a 32% lower value than the temperature underneath the drain end of the gate acquired from the ITO-gated device. This underestimation of temperature could result in overestimation of the component lifetime during accelerated operational life tests. 

Several research studies have investigated the degradation of BaTiO3-based dielectric capacitor materials, focusing on the impact of composition, defect chemistry, and microstructural design to limit the electromigration of oxygen vacancies under electric fields at finite temperatures. Electromigration can be a dominant mechanism that controls failure rates in the individual multilayer ceramic capacitor (MLCC) components in testing the reliability of failures with highly accelerated lifetime testing (HALT) to determine the mean time to failure of MLCCs surface mounted onto printed circuit boards (PCBs). Conventional assumptions often consider these failures as independent, with no interaction between components on the PCB. However, this study employs a Physics of Failure (PoF) approach to closely examine transient degradation and its impact on MLCC reliability, emphasizing thermal crosstalk and its influence on dependent and independent failure rates. Finite element analysis thermal modeling and infrared thermography were used to assess the impact of circuit layout and component spacing on heat dissipation and thermal crosstalk under various electrical stress conditions. The study distinguishes between dependent and independent failures under a HALT, quantified through a β′ factor reflecting common cause failures due to thermal crosstalk. Through a series of experimental and statistical analyses, the β′ factor is evaluated with respect to temperature, voltage, and component spacing. These insights highlight the importance of understanding the nature of the data in reliability testing of MLCCs and optimizing the layout design of high-density circuits to mitigate dependent failures, improving overall reliability and informing better design and packaging strategies. 

Gallium nitride (GaN)-based high electron mobility transistors (HEMTs) are essential components in modern radio frequency power amplifiers. In order to improve both the device electrical and thermal performance (e.g., higher current density operation and better heat dissipation), researchers are introducing AlN into the GaN HEMT structure. The knowledge of thermal properties of the constituent layers, substrates, and interfaces is crucial for designing and optimizing GaN HEMTs that incorporate AlN into the device structure as the barrier layer, buffer layer, and/or the substrate material. This study employs a multi-frequency/spot-size time-domain thermoreflectance approach to measure the anisotropic thermal conductivity of (i) AlN and GaN epitaxial films, (ii) AlN and SiC substrates, and (iii) the thermal boundary conductance for GaN/AlN, AlN/SiC, and GaN/SiC interfaces (as a function of temperature) by characterizing GaN-on-SiC, GaN-on-AlN, and AlN-on-SiC epitaxial wafers. The thermal conductivity of both AlN and GaN films exhibits an anisotropy ratio of ∼1.3, where the in-plane thermal conductivity of a ∼1.35 μm thick high quality GaN layer (∼223 W m−1 K−1) is comparable to that of bulk GaN. A ∼1 μm thick AlN film grown by metalorganic chemical vapor deposition possesses a higher thermal conductivity than a thicker (∼1.4 μm) GaN film. The thermal boundary conductance values for a GaN/AlN interface (∼490 MW m-2 K−1) and AlN/SiC interface (∼470 MW m−2 K−1) are found to be higher than that of a GaN/SiC interface (∼305 MW m−2 K−1). This work provides thermophysical property data that are essential for optimizing the thermal design of AlN-incorporated GaN HEMT devices. 

Lead zirconate titanate (PZT) thin films offer advantages in microelectromechanical systems (MEMSs) including large motion, lower drive voltage, and high energy densities. Depending on the application, different substrates are sometimes required. Self-heating occurs in the PZT MEMS due to the energy loss from domain wall motion, which can degrade the device performance and reliability. In this work, the self-heating of PZT thin films on Si and glass and a film released from a substrate were investigated to understand the effect of substrates on the device temperature rise. Nano-particle assisted Raman thermometry was employed to quantify the operational temperature rise of these PZT actuators. The results were validated using a finite element thermal model, where the volumetric heat generation was experimentally determined from the hysteresis loss. While the volumetric heat generation of the PZT films on different substrates was similar, the PZT films on the Si substrate showed a minimal temperature rise due to the effective heat dissipation through the high thermal conductivity substrate. The temperature rise on the released structure is 6.8× higher than that on the glass substrates due to the absence of vertical heat dissipation. The experimental and modeling results show that the thin layer of residual Si remaining after etching plays a crucial role in mitigating the effect of device self-heating. The outcomes of this study suggest that high thermal conductivity passive elastic layers can be used as an effective thermal management solution for PZT-based MEMS actuators. 

The ultra-wide bandgap (UWBG) energy (∼5.4 eV) of α-phase Ga2O3 offers the potential to achieve higher power switching performance and efficiency than today's power electronic devices. However, a major challenge to the development of the α-Ga2O3 power electronics is overheating, which can degrade the device performance and cause reliability issues. In this study, thermal characterization of an α-Ga2O3 MOSFET was performed using micro-Raman thermometry to understand the device self-heating behavior. The α-Ga2O3 MOSFET exhibits a channel temperature rise that is more than two times higher than that of a GaN high electron mobility transistor (HEMT). This is mainly because of the low thermal conductivity of α-Ga2O3 (11.9 ± 1.0 W/mK at room temperature), which was determined via laser-based pump-probe experiments. A hypothetical device structure was constructed via simulation that transfer-bonds the α-Ga2O3 epitaxial structure over a high thermal conductivity substrate. Modeling results suggest that the device thermal resistance can be reduced to a level comparable to or even better than those of today's GaN HEMTs using this strategy combined with thinning of the α-Ga2O3 buffer layer. The outcomes of this work suggest that device-level thermal management is essential to the successful deployment of UWBG α-Ga2O3 devices. 

Gallium nitride (GaN) high electron mobility transistors (HEMTs) are key components of modern radio frequency (RF) power amplifiers. However, device self-heating negatively impacts both the performance and reliability of GaN HEMTs. Accordingly, laser-based pump-probe methods have been used to characterize the thermal resistance network of epitaxial material stacks that are used to fabricate HEMT structures. However, validation studies of these measurement results at the device level are lacking. In the present work, a GaN-on-SiC wafer was characterized using frequency-domain thermoreflectance and steady-state thermoreflectance techniques. The thermal conductivity of the GaN channel/buffer layer, SiC substrate, and the interfacial thermal boundary resistance at the GaN/SiC interface were determined. Results were validated by performing thermal imaging and modeling of a transmission line measurement (TLM) structure fabricated on the GaN-on-SiC wafer. 

Gallium nitride (GaN) high electron mobility transistors (HEMTs) are key components enabling today’s wireless communication systems. However, overheating concerns hinder today’s commercial GaN HEMTs from reaching their full potential. Therefore, it is necessary to characterize the respective thermally resistive components that comprise the device’s thermal resistance and determine their contributions to the channel temperature rise. In this work, the thermal conductivity of the GaN channel/buffer layer and the effective thermal boundary resistance (TBR) of the GaN/substrate interface of a GaN-on-SiC wafer were measured using a frequency-domain thermoreflectance technique. The results were validated by both experiments and modeling of a transmission line measurement (TLM) structure fabricated on the GaN-on-SiC wafer. The limiting GaN/substrate thermal boundary conductance (TBC) beyond which there is no influence on the device temperature rise was then quantified for different device configurations. It was determined that this limiting TBC is a function of the substrate material, the direction in which heat primarily flows, and the channel temperature. The outcomes of this work provide device engineers with guidance in the design of epitaxial GaN wafers that will help minimize the device’s thermal resistance.